Now showing 1 - 10 of 14
  • Publication
    Interpretation of In Situ and Laboratory Thermal Measurements Resulting in Accurate Thermogeological Characterisation
    (Taylor & Francis, 2012-09) ;
    Growing worldwide interest in the exploitation of geothermal energy resources has led to a scenario where the technology routinely forms part of building-scale renewable energy feasibility studies. A thorough understanding of site-specific thermogeological parameters is a vital design requirement of such systems and accurate measurement and interpretation of these parameters is necessary in order to inform scientifically rigorous system design. An overview of the theory underlying a number of laboratory and in situ thermal characterization testing methods and the results from a number of testing regimes carried out using the various thermal characterization equipment constructed in University College Dublin are presented. Results from both the laboratory steady-state and non-steady-state thermal analysis systems and the in situ thermal characterization system are shown to provide accurate measurements of soil and rock thermal parameters. In addition, the settlement profiles of a number of the tested materials were investigated in order to gain an in-sight into this potential drawback of exchanging the backfill material placed around electricity cables to optimize thermal transfer efficiency.
      593
  • Publication
    Design and development of a low-cost thermal response rig
    (Institution of Civil Engineers, 2012-08-01) ;
    A thermal response test (TRT) is a controlled insitu test during which a known quantity of heat energy is injected into a closed loop heat-exchanger pipe while the heat dissipation rate into the surrounding ground is monitored. Results from a test can be interpreted to determine a number of ground thermal parameters with are vital design requirements for any medium to large scale ground source energy system. This paper describes the design and construction of a low cost TRT rig and compares the results obtained from a test using the constructed rig and a commercially built rig in order to evaluate the accuracy of the constructed equipment. The TRT rig is designed in accordance with the following principles: keep construction costs low, improve the cost-efficiency of TRT testing by incorporating remote data transmission capability and ensure attainment of sufficient accuracy to satisfy the design requirements of ground source energy systems. Analysis of data collected by the TRT rigs result in a calculated thermal conductivity of 1.9 W/mK in both cases. This value falls within the range expected for the tested geological formation and confirms the accuracy of both test rigs.
    Scopus© Citations 5  2063
  • Publication
    A preliminary study of the effect of groundwater flow on the thermal front created by borehole heat exchangers
    This paper presents an analysis performed using a coupled TEMP/W-SEEP/W finite element model to consider both the conducive and convective effects of groundwater flow on the thermal regime created by a ground source energy system. The change in the development of the sub-surface thermal regime created by ground source energy borehole heat exchangers caused by a groundwater flow across a site, relative to a scenario where groundwater flow does not exist is examined. Analysis is performed using finite element formulations of both single borehole and multi borehole systems. The results of this work show that even a modest groundwater flow across a site can lead to a significant change in the development of the sub-surface thermal regime. It also shows that groundwater flow can result in implications for: proposed developments incorporating ground source energy systems; nearby existing ground source energy systems; potential future nearby ground source energy systems and the use of established software packages currently used for the design of ground source energy systems in the industry.
    Scopus© Citations 8  424
  • Publication
    Thermal response testing of compromised borehole heat exchangers
    (Oxford University Press, 2012-03-19) ;
    The results of five thermal response tests (TRTs) are presented. Three of the tests were carried out consecutively on the same borehole to illustrate the importance of allowing artificially imposed thermal gradients to dissipate prior to commencement or re-commencement of a test following testing issues. The two remaining tests carried out on separate boreholes confirm the results obtained by the first(uncompromised) of the initial three tests. The testing regime demonstrates the necessity of careful performance of TRT’s and shows the variation in costs/required borehole length which may occur if testing problems occur on site.
    Scopus© Citations 3  609
  • Publication
    Energy piles: site investigation and analysis
    (Thomas Telford Ltd., 2013-09-05) ;
    Despite an increasing worldwide use of geothermal energy foundations, there is a lack of published guidelines and results from thermal response testing of such installations. In this paper the results are presented from thermal response, thermal recovery and laboratory thermal testing performed at two sites in Ireland. Some practical issues concerned with the use of thermal response testing rigs, designed for use with deep boreholes, on relatively short piles are discussed and addressed. Given the relatively short geothermally active depth of the energy foundations tested, and the fact that the University College Dublin thermal response testing rig has been designed primarily for testing on medium and deep geothermal boreholes, thermal response tests of shorter durations than are normally used for deep boreholes were performed. The techniques used to analyse the various test results are outlined, and the resulting values of thermal conductivity obtained are within the range of those expected for the prevailing geology of the sites.
    Scopus© Citations 17  1315
  • Publication
    Monitoring environmental parameters in poultry production facilities
    (Institute for Process and Particle Engineering, Graz University of Technology, Austria, 2013-04) ; ; ;
    Increases in fuel and feed prices are placing a significant burden on the poultry industry in Ireland and worldwide. For producers to meet their financial targets, increased performance and output is a key issue, now more than ever. To optimise performance in broiler production houses, the effect of environmental and air quality parameters on bird performance and energy consumption must be known to allow farmers make informed management decisions. This paper concentrates on the application precision livestock farming sensors to develop recommendations for improved bird performance and energy consumption in broiler production farms in Ireland.   Air temperature, relative humidity, light, air speed and air quality (in particular CO2 and NH3 concentrations) are identified as important parameters for improving bird performance and energy consumption in broiler production houses. Several of these parameters (temperature, relative humidity, CO2 and NH3) were monitored on two farms during the study over the initial 2 weeks of the production cycle. Air quality was often overlooked during the production process, as farmers struggled to limit high heating and feed costs. However, elevated levels of CO2 (>3000 ppm) did not appear to affect broiler growth rates. Additionally, a strong correlation was observed between relative humidity and NH3 (R2 = 0.86 - 0.92). Producers tend to use relative humidity as an indication for NH3 levels and the research shown in this study confirms the close relationship between the two parameters. It is recommended that further data should be gathered from producing units and novel performance technologies should also be investigated.
      5654
  • Publication
    Design and development of a low-cost divided bar apparatus
    A divided bar apparatus is deemed to be the most accurate method of measuring the thermal conductivity, λ, (W/mK) of intact rock cores in the laboratory. The divided bar is a steady-state comparative method in which the temperature drop across a disk of rock is compared with that across a disk of standard material of known conductivity. Thermal conductivity test results obtained from rock cores can be used in software programs to determine the design requirements for any medium to large-scale ground-source energy system. This paper describes the design and development of a low-cost divided bar apparatus and compares the values obtained to those achieved by previous researchers and those recommended by EED, a commonly used borehole heat exchanger design software program. The divided bar was designed in accordance with the following principles: keep construction costs low by using readily available materials, develop a simplistic operating procedure to promote continuity of use and cater for the testing of different sized rock cores. As there are currently no recognised testing standards available for operation of a divided bar apparatus, the sample preparation procedure for samples tested on the UCD divided bar apparatus was developed as a proposed standard testing procedure. The proposed procedure amalgamates the developments and suggestions of previous researchers in addition to published test procedures in Ulusay and Hudson (2007), and could possibly contribute towards the development of a standardised procedure for testing on a divided bar apparatus. The test results presented in this paper demonstrate a strong relationship between thermal conductivity and mineral composition with the effects of porosity also having a notable influence on the thermal conductivity of the tested rocks.
    Scopus© Citations 8  910
  • Publication
    Geothermal energy : settlement and water chemistry in Cork, Ireland
    (Institution of Engineers, 2011-07) ;
    Detailed analysis of potential water chemistry and settlement issues associated with the installation of open-loop geothermal systems is infrequently carried out. This has led to the failure of several previously installed systems. Chemical analysis of water extracted from beneath the Cork docklands, Ireland has been performed by the authors in order to assess the suitability of the area for the exploitation of open-loop geothermal energy. The possibility of settlement induced by pumping of groundwater for open-loop systems has also been examined. Current market penetration of ground source heat pumps in Ireland is discussed to illustrate the infancy of the technology in Ireland relative to other European countries and to highlight the necessity of approaching the possible installation of such systems with the care required. Water extracted from beneath the docklands shows that significant water chemistry issues exist. Laboratory and field tests confirm that optimal concentration levels of several water chemistry characteristics are significantly exceeded; leading to the conclusion that open-loop exploitation in the area may not be suitable. In addition, settlement induced by pumping of water could potentially lead to a consolidation settlement in excess of 30 mm due primarily to the existence of highly compressible alluvium.
    Scopus© Citations 6  1476
  • Publication
    Developing Geothermal Energy Research Capabilities at University College Dublin
    (Geothermal Association of Ireland, 2011) ;
    Ireland has one of the highest energy dependencies in Europe and as such must adapt quickly to increase renewable energy exploitation levels in order to secure its energy future. A mix of renewable energy technology types (wind, solar, biomass, wave, tidal, geothermal) will be required in order to achieve Ireland’s national renewable energy generation targets. Geothermal (or ground source) energy can have a part to play in this mix. Over the last number of years the School of Civil, Structural & Environmental Engineering in University College Dublin has begun to develop shallow geothermal energy research capabilities in several areas of interest. Early studies involved the investigation of water chemistry and settlement issues at several sites on the Cork docklands. It was concluded that the chemical characteristics of the water contained in the aquifer could hinder the development of open loop geothermal systems in the area, and that settlement may be a potential concern in cases where open loop systems are installed due to the presence of highly compressible alluvium deposits. Subsequent work has involved the development, construction & performance validation of a thermal response testing rig for site thermal characterisation, installation of both domestic and commercial sized energy piles for research purposes and investigation of soil, rock and grout thermal properties using both steady-state and non-steady-state laboratory testing techniques. This paper gives a brief overview of the completed and ongoing work in the School of Civil, Structural & Environmental Engineering.
      3472
  • Publication
    Analysis of bed agglomeration during gasification of wheat straw in a bubbling fluidised bed gasifier using mullite as bed material
    The quantity and composition of the ash content of straw poses technical challenges to its thermal conversion and have been widely reported to cause severe ash sintering and bed agglomeration during fluidised bed gasification. Literature indicates that a combination of reactor design and bed material measures is required to avoid defluidisation at temperatures above 800 °C. Using scanning electron microscopy and energy dispersive X-ray spectroscopy this study investigated the initial agglomeration of a mullite bed during the gasification of wheat straw in a small scale, air blown bubbling fluidised bed. The results show that the temperatures along the height of the bed converge prior to any marked drop in pressure or heating of the lower freeboard. This convergence was seen to occur at temperatures close to 750 °C in repeated gasification experiments. Energy dispersive X-ray spectroscopy indicates coating-induced agglomeration caused by the reaction of alkali metals with silica. Scanning electron microscopy under high magnification revealed a layered structure to the agglomerates, where ash particles are subsumed into a fused material. This suggests the formation of agglomerates by the three step agglomeration process postulated by other authors. Analysis of indices used to predict agglomeration on the basis of a fuel's ash content and composition indicates that the Alkali Index is the most accurate, successfully predicting agglomeration for 7 of the 9 fuels where agglomeration was observed.
    Scopus© Citations 30  993