Options
NĂ Annaidh, Aisling
Preferred name
NĂ Annaidh, Aisling
Official Name
NĂ Annaidh, Aisling
Research Output
Now showing 1 - 10 of 17
- PublicationA combined experimental and numerical study of stab-penetration forcesThe magnitude of force used in a stabbing incident can be difficult to quantify, although the estimate given by forensic pathologists is often seen as 'critical' evidence in medico-legal situations. The main objective of this study is to develop a quantitative measure of the force associated with a knife stabbing biological tissue, using a combined experimental and numerical technique. A series of stab-penetration tests were performed to quantify the force required for a blade to penetrate skin at various speeds and using different 'sharp' instruments. A computational model of blade penetration was developed using ABAQUS/EXPLICIT, a non-linear finite element analysis (FEA) commercial package. This model, which incorporated element deletion along with a suitable failure criterion, is capable of systematically quantifying the effect of the many variables affecting a stab event. This quantitative data could, in time, lead to the development of a predictive model that could help indicate the level of force used in a particular stabbing incident.
768Scopus© Citations 32 - PublicationToward a Predictive Assessment of Stab-Penetration Forces(Ovid Technologies (Wolters Kluwer) - Lippincott Williams & Wilkins, 2014-04)
; ; ; Collaborative research between the disciplines of forensic pathology and biomechanics was undertaken to investigate the hyperelastic properties of human skin, to determine the force required for sharp instrument penetration of skin, and to develop a finite element model, which reflects the mechanisms of sharp instrument penetration. These studies have led to the development of a "stab metric," based on simulations, to describe the force magnitudes in stabbing incidents. Such a metric should, in time, replace the crudely quantitative descriptors of stabbing forces currently used by forensic pathologists.316Scopus© Citations 11 - PublicationThe Importance of the Scalp in Head Impact KinematicsThe best way to reduce the risk of head injury (up to 69% reduction) is to wear a helmet. In recent years, the improvement of helmet standard tests focused on reproducing realistic impact conditions and including the effect of rotational acceleration. However, less importance has been given to the development of a realistic headform. The goal of this work was to evaluate the role of scalp tissue in head impact kinematics; both with respect to its mechanical properties and with respect to its sliding properties. An EN960 and HIII headform were subjected to linear and oblique impacts, respectively, both with and without porcine scalp attached. Different speeds, impact locations and impact surfaces were tested. Standard linear drop tests (EN960) showed that the scalp reduced the impact energy by up to 68.7% (rear impact). Oblique head impact tests showed how the headform-anvil friction coefficient changes when the HIII is covered with scalp, affecting linear and rotational accelerations. Therefore, the scalp plays an important role in head impacts and it should be realistically represented in headforms used for impact tests and in numerical models of the human head.
465Scopus© Citations 21 - PublicationTowards a predictive assessment of stab-penetration forces(Lippincott, Williams and Wilkins, 2015-09)
; ; ; ; Collaborative research between the disciplines of forensic pathology and biomechanics was undertaken to investigate the hyperelastic properties of human skin, to determine the force required for sharp instrument penetration of skin, and to develop a finite element model, which reflects the mechanisms of sharp instrument penetration. These studies have led to the development of a 'stab metric', based on simulations, to describe the force magnitudes in stabbing incidents. Such a metric should, in time, replace the crudely quantitative descriptors of stabbing forces currently used by forensic pathologists.415Scopus© Citations 11 - PublicationManufacturing custom-contoured wheelchair seating: A state-of-the-art reviewBackground: Custom-contoured wheelchair seating lowers risk of pressure injury and postural deterioration while custom-contoured wheelchair seating lowers risk of pressure injury and postural deterioration while increasing the stability and functional activity of the wheelchair occupant. Producing custom-contoured seating systems has historically been a labour-intensive process custom-contoured seating systems is historically labour-intensive. Objectives: Evaluate the strengths and limitations of current manufacturing processes for custom-contoured wheelchair seating to suggest potential future manufacturing processes. Study Design: Literature review of the state of the art. Methods: Research conducted through a literature review focused on the performance of different types of custom-contoured wheelchair seating products and processes over the last 40 years. Recent literature in orthotics and prosthetics was also consulted to assess future trends in seating. Results: There are five main manufacturing processes currently used to produce custom-contoured wheelchair seating systems. No single process is yet suitable for all wheelchair users, but many manufacturers are transitioning to computer numerical controlled (CNC) milling to reduce manual labour. Adjustable micro-modular seating and moulded seat insert manufacturing are also prevalent and offer alternative seating to soft foam carving. Conclusion: There is a need in the custom wheelchair seating sector for processes that are fast, cost-effective, produce little to no material waste, and that can effectively maintain a comfortable seating micro-climate. Additive manufacturing may meet these criteria, but further evaluation is required. Clinical relevance: This review suggests that the custom-contoured wheelchair seating manufacturers are moving away from labour-intensive processes towards digital techniques, like CNC foam milling. Additive manufacturing is a potential new process that may reduce overall costs, the lead time in preparing seats and has the potential to better manage the seating micro-climate.
Scopus© Citations 6 1993 - PublicationDeficiencies in numerical models of anisotropic nonlinearly elastic materialsIncompressible nonlinearly hyperelastic materials are rarely simulated in finite element numerical experiments as being perfectly incompressible because of the numerical difficulties associated with globally satisfying this constraint. Most commercial finite element packages therefore assume that the material is slightly compressible. It is then further assumed that the corresponding strain-energy function can be decomposed additively into volumetric and deviatoric parts. We show that this decomposition is not physically realistic, especially for anisotropic materials, which are of particular interest for simulating the mechanical response of biological soft tissue. The most striking illustration of the shortcoming is that with this decomposition, an anisotropic cube under hydrostatic tension deforms into another cube instead of a hexahedron with non-parallel faces. Furthermore, commercial numerical codes require the specification of a 'compressibility parameter' (or 'penalty factor'), which arises naturally from the flawed additive decomposition of the strain-energy function. This parameter is often linked to a 'bulk modulus', although this notion makes no sense for anisotropic solids; we show that it is essentially an arbitrary parameter and that infinitesimal changes to it result in significant changes in the predicted stress response. This is illustrated with numerical simulations for biaxial tension experiments of arteries, where the magnitude of the stress response is found to change by several orders of magnitude when infinitesimal changes in 'Poisson’s ratio' close to the perfect incompressibility limit of 1/2 are made.
Scopus© Citations 35 588 - PublicationBending instabilities of soft biological tissuesRubber components and soft biological tissues are often subjected to large bending deformations while 'in service'. The circumferential line elements on the inner face of a bent block can contract up to a certain critical stretch ratio λcr (say) before bifurcation occurs and axial creases appear. For several models used to describe rubber, it is found that λcr=0.56, allowing for a 44% contraction. For models used to describe arteries it is found, somewhat surprisingly, that the strain-stiffening effect promotes instability. For example, the models used for the artery of a seventy-year old human predict that λcr=0.73, allowing only for a 27% contraction. Tensile experiments conducted on pig skin indicate that bending instabilities should occur even earlier there.
302Scopus© Citations 76 - PublicationCharacterization of the anisotropic mechanical properties of excised human skin(Elsevier, 2012-01)
; ; ; ; The mechanical properties of skin are important for a number of applications including surgery, dermatology, impact biomechanics and forensic science. In this study, we have investigated the influence of location and orientation on the deformation characteristics of 56 samples of excised human skin. Uniaxial tensile tests were carried out at a strain rate of 0.012 s−1 on skin from the back. Digital Image Correlation was used for 2D strain measurement and a histological examination of the dermis was also performed. The mean ultimate tensile strength (UTS) was 21.6±8.4 MPa, the mean failure strain 54%±17%, the mean initial slope 1.18±0.88 MPa, the mean elastic modulus 83.3±34.9 MPa and the mean strain energy was 3.6±1.6 MJ/m3. A multivariate analysis of variance has shown that these mechanical properties of skin are dependent upon the orientation of the Langer lines (P<0.0001−P=0.046). The location of specimens on the back was also found to have a significant effect on the UTS (P=0.0002), the elastic modulus (P=0.001) and the strain energy (P=0.0052). The histological investigation concluded that there is a definite correlation between the orientation of the Langer lines and the preferred orientation of collagen fibres in the dermis (P<0.001). The data obtained in this study will provide essential information for those wishing to model the skin using a structural constitutive model.407Scopus© Citations 494 - PublicationEvaluation of the head-helmet sliding properties in an impact testThe scalp plays a crucial role in head impact biomechanics, being the first tissue involved in the impact and providing a sliding interface between the impactor and/or helmet and the skull. It is important to understand both the scalp-skull and the scalp-helmet sliding in order to determine the head response due to an impact. However, experimental data on the sliding properties of the scalp is lacking. The aim of this work was to identify the sliding properties of the scalp using cadaver heads, in terms of scalp-skull and scalp-liner (internal liner of the helmet) friction and to compare these values with that of widely used artificial headforms (HIII and magnesium EN960). The effect of the hair, the direction of sliding, the speed of the test and the normal load were considered. The experiments revealed that the sliding behaviour of the scalp under impact loading is characterised by three main phases: (1) the low friction sliding of the scalp over the skull (scalp-skull friction), (2) the tensioning effect of the scalp and (3) the sliding of the liner fabric over the scalp (scalp-liner friction). Results showed that the scalp-skull coefficient of friction (COF) is very low (0.06 ± 0.048), whereas the scalp-liner COF is 0.29 ± 0.07. The scalp-liner COF is statistically different from the value of the HIII-liner (0.75 ± 0.06) and the magnesium EN960-liner (0.16 ± 0.026). These data will lead to the improvement of current headforms for head impact standard tests, ultimately leading to more realistic head impact simulations and the optimization of helmet designs.
408Scopus© Citations 37 - PublicationAdditive Manufacture of Composite Soft Pneumatic Actuators(Mary Ann Liebert, 2018-12-07)
; ; ; ; ; ; This article presents a direct additive manufacturing method for composite material soft pneumatic actuators that are capable of performing a range of programmable motions. Commonly, molding is the method used to manufacture soft fluidic actuators. This is material, labor, and time intensive and lacks the design freedom to produce custom actuators efficiently. This article proposes an alternative semiautomated method of designing and manufacturing composite soft actuators. An affordable, open-source, desktop three-dimensional (3D) printer was modified into a four-axis, combined, fused deposition modeling, and paste extrusion printer. A Grasshopper 3D algorithm was devised to implement custom actuator designs according to user inputs, resulting in a G-code print file. Bending, contracting, and twisting motion actuators were parametrically designed and subsequently additively manufactured from silicone and thermoplastic elastomer (TPE) materials. Experimental testing was completed on these actuators along with their constitutive materials. Finite element models were created to simulate the actuator's kinematic performance. Having a platform method to digitally configure and directly additively manufacture custom-motion, composite soft actuators has the potential to accelerate the development of more intricate designs and lead to potential impacts in a range of areas, including in-clinic personalization of soft assistive devices and patient-specific biomedical devices.1402Scopus© Citations 42